Article collections

All Items

• Analysis of Damage to the Induce Draft Fan Component at PLTU PT. XYZ

  Wilarso Wilarso, Awang Surya, Asep Saepudin, Muhamad Ali Pahmi

  123-130

• Analysis of the Effect of Phase Change Material Mass Variation on the Performance of an Air-Cooled Photovoltaic-Thermal System Analisis Pengaruh Variasi Massa Phase Change Material terhadap Kinerja Sistem Photovoltaic Thermal Berbasis Pendingin Udara

  Muhammad Alvan Fadillah, Udin Komarudin, Ahmad Rajani

  263-270

• Analysis of Thermal Effectiveness and Mass Flow Rate of Steam from Saturated to Superheater in Palm Oil Mill Analisis Efektivitas Thermal dan Laju Aliran Massa Steam dari Saturated Menuju Superheater di Pabrik Kelapa Sawit

  Andhi Fuad Bawazir, Zulham Effendi

  211-218

• Application of Linear Programming to Reduce Traffic Congestion in Urban Centers: A Case Study of Lagos State Transport Authority

  Anthony Adekoya, Wasiu Adedeji, Seun Oyelami, Busayo Adeboye

  219-226

• Chemical Modification of Petung Bamboo Fiber to Hybrid Composites Modifikasi Kimia Serat Bambu Petung terhadap Komposit Hibrida

  Raden Muhammad Yusron Maulana, Rahma Rei Sakura, Nasrul Ilminnafik, Sumarji, Mahros Darsin

  139-148

• Configuration Analysis of Mainsteam Stop Valve-Governor Valve in a Supercritical Steam Turbine Using Computational Fluid Dynamics to Minimize Throttle Losses

  Jauhar Fahmi, S. Silviana, Sulistyo

  219-228

• Design and Experimental Evaluation of a Low-Power Organic Waste Shredder with Conveyor Feeding Mechanism

  Wilarso Wilarso, Riyan Mardiyana

  291-300

• Design and Fabrication of a Modular Mini-Hydro Turbine for Off-Grid Electrification in Nigeria’s Riverine Communities

  Hyginus Unegbu, Danjuma YAWAS

  1-14

• Design and Manufacturing of the Steering System in the KMHE Laksamana V 1.0 Prototype Vehicle

  Budi Istana, Aydil Hijerah Harahap, Sunaryo

  115-122

• Development of a Waste Plastic-to-Fuel Conversion System for Sustainable Energy Generation in Urban Nigeria

  Hyginus Unegbu, Danjuma YAWAS

  195-206

• Effect of Anadara Granosa Shell Volume Fraction on Erosive Wear and Hardness Behaviour of Al 6061 Metal Matrix Composites

  Riki Hendra Purba, Aldi Raditya Adriansyah, James Julian, Fitri Wahyuni, Elvi Armadani, Fathin Muhammad Mahdhudhu

  25-36

• Effect of Flow Disturbance Geometry on Thermal Hydraulic Performance of Forced Air-Cooled Heat Sinks for CPU Cooling

  Annisa Fitriola Suryawati, Damora Rhakasywi, Nicky Yongkimandalan, Bima Rakha Adhitama

  179-188

• Effect of T6 Heat Treatment on Tensile Strength and Hardness of A356 Aluminum Alloy at 720°C Optimization Pengaruh Perlakuan Panas T6 terhadap Kekuatan Tarik dan Kekerasan Paduan Aluminium A356 pada Optimasi Suhu 720°C

  Wawan Budi, Johan Alfian Pradana, Bamban Handriyanto, Nazri Syah Rizan, Saiful Rowi, Ahmad Bazi Syarif

  143-148

• The Effect of Variations in the Composition of Cocoa Shell Charcoal and Peanut Shell Charcoal on Briquette Characteristics

  Ahmad Akromul Huda, Akbar Tawaqqal, Syarif Hidayatullah, Nurdin Juniardi

  131-138

• Efficiency and Electrical Power Consumption of Prototype-2 Gasification Stove Fueled by Used Cooking Oil

  Purwandito Tulus Asmoro, Dani Usman, Feri Siswoyo Hadisantoso, Dwi Nurcahyo, Gimas Sahrul Sopanji

  187-194

• Energy Performance Analysis of the Crushing Area at PT. X Using Energy Performance Indicators (EnPI) Based on ISO 50001:2018 Analisis Kinerja Energi pada Area Crushing di PT. X Menggunakan Energy Performance Indicator (EnPI) Berdasarkan ISO 50001:2018

  Arifia Ekayuliana, Andi Ulfiana, Carelita Maulidi Agnia, Asep Apriana, Ahmad Bustomi

  281-290

• Evaluation of the Design for the Construction of a 100 kW Micro Hydropower Plant (PLTMH) Utilizing Condenser Cooling Water Discharge at a 2×25 MW Coal-Fired Power Plant (CFPP)

  Khoeruz zaman, Jaka Windarta, Sulistyo

  63-76

• Expert System Application for Production Planning and Control Optimization in Jobshop Manufacturing: A Review for Developing Economies

  Abiodun Gbemileke ABIOYE, Musibaudeen Olatunde IDRIS , Olakunle OLUKAYODE , Oriyomi O. ADETAYO, Abdulhafiz Ademola ADEFAJO , Babajide Joshua OJERINDE

  301-316

• FDM 3D Printing Process Optimization for PLA-Based Bearing Components Using the Taguchi Method Optimasi Proses Cetak 3D FDM untuk Komponen Bearing Berbasis PLA Menggunakan Metode Taguchi

  Wahyu Dwi Lestari Lestari, Sania Nadillah Permata Dewi

  207-218

• Finite Element Evaluation of Torsional Deformation and Stress Distribution in a Pump-Turbine Shaft System Evaluasi Elemen Hingga terhadap Deformasi Torsi dan Distribusi Tegangan pada Sistem Poros Pompa-Turbin

  Rizki Sopandi, Adhita Prasetia, Udin Komarudin

  239-252

• Implementation of Green Manufacturing in Cocoa Butter Substitute (CBS) Production: A Case Study at PT Unilever Oleochemical Indonesia Implementasi Green Manufacturing pada Produksi Cocoa Butter Substitute (CBS): Studi Kasus di PT Unilever Oleochemical Indonesia

  Putut Ade Irawan, Luhur Pambudi Herdanarpati, Johan Alfian Pradana, Hari Irawan

  47-54

• Improving the Quality of Cake Mold Products Through the Integration of Green Manufacturing and Good Manufacturing Practice (GMP) Using the KPI, FMEA, and Fishbone Diagram Approaches Peningkatan Mutu Produk Cetakan Kue Melalui Integrasi Green Manufacturing dan Good Manufacturing Practice (GMP) Menggunakan Pendekatan KPI, FMEA, dan Fishbone Diagram

  Lolyka Dewi Indrasari, Johan Alfian Pradana, Ana Komari, Afiff Yudha Tripariyanto, Venus Khatta S

  37-46

• Machine Learning-Based Modeling of Boiler Efficiency: Impact Analysis of Operational Variables Using Random Forest, XGBoost, and ANN

  Muhamad Iqbal Syachjaya Syachjaya, Heri Sutanto , Marcelinus Christwardana , Subhan Hasisi, Napolin Niuhardson Siregar

  157-168

• Multi-Objective Optimization for Uncertainty Management in Circular Economy: An Empirical Approach to the Yellow Tofu Industry in Kediri

  Ana Komari, Lolyka Dewi Indrasari

  133-142

• Multi-Response Optimization of Mechanical Properties and Quantitative Porosity of A356 Aluminum Alloy Subjected to T6 Heat Treatment Using Response Surface Methodology Optimasi Multi-Respons Sifat Mekanik dan Porositas Kuantitatif Paduan Aluminium A356 pada Perlakuan Panas T6 Menggunakan Response Surface Methodology

  Joni Arif, syaiful arif, Widarto, Ardian Maulana

  317-326