Analysis of Damage to the Induce Draft Fan Component at PLTU PT. XYZ

Authors

  • Wilarso Wilarso Universitas Muhammadiyah Cileungsi, Indonesia
  • Awang Surya Universitas Muhammadiyah Cileungsi, Indonesia
  • Asep Saepudin Universitas Muhammadiyah Cileungsi, Indonesia
  • Muhamad Ali Pahmi Universitas Muhammadiyah Cileungsi, Indonesia

Keywords:

Induce Draft Fan (IDF), PLN generators

Abstract

Damage to the Induce Draft Fan (IDF), will impact to the combustion system which serves to provide Secondary Air to meet the air needs of the combustion system in the furnace in the boiler. There are 2 IDFs in the generating unit which are operated simultaneously or alternately. The purpose of this research is to determine the damage to the IDF so that there is no decrease in power supply to PLN generators. The method used in this study used fishbone analysis. Based on the analysis, the IDF damage occurs due to abrasion on the fan blade which is caused by the blade surface in contact with the abrasive material (Fe2O3) on the flue gas. The malfunctioning of the Electrostatic Precipitator (ESP) causes the abrasive material (Fe2O3) in the flue gas to not flow to the IDF, thus damaging the blade

References

[1] J. Li and W. Li, “Axial Flow PAF Accident Analysis and Solutions of Thermal Power Unit,” no. Ap3er, pp. 5–8, 2015, doi: 10.2991/ap3er-15.2015.2.

[2] A. S. N. Chairat and R. Yuda, “Analisa Kapasitas Force Draft Fan Dengan Bahan Bakar Batubara Kualitas Rendah,” J. Power Plant, pp. 6–11, 2016.

[3] L. Waldheim, Gasification of waste for energy carriers. A review, vol. Task 33. 2018.

[4] M. S. Bhowmick and S. C. Bera, “Study the performances of induced fans and design of new induced fan for the efficiency improvement of a thermal power plant,” IEEE Reg. 10 Colloq. 3rd Int. Conf. Ind. Inf. Syst. ICIIS 2008, no. January 2009, 2008, doi: 10.1109/ICIINFS.2008.4798468.

[5] M. Nurbanasari, T. Kristyadi, T. S. Purwanto, A. Maulana, and R. R. Fadilah, “Damage analysis of the forced draft fan blade in coal fired power plant,” Case Stud. Eng. Fail. Anal., vol. 8, no. February, pp. 49–56, 2017, doi: 10.1016/j.csefa.2017.04.005.

[6] A. F. Mohamed, M. E. Habash, M. S. Alsoufi, and M. K. Hassan, “Failure analysis of flue gas duct in a steam power plant,” Int. J. Mech. Mechatronics Eng., vol. 20, no. 1, 2020.

[7] J. Du, J. Liang, and L. Zhang, “Research on the failure of the induced draft fan’s shaft in a power boiler,” Case Stud. Eng. Fail. Anal., vol. 5–6, pp. 51–58, 2016, doi: 10.1016/j.csefa.2016.02.002.

[8] P. K. Bhatia, A. Naithani, B. Parashar, and G. Taneja, “Available online through www.ijma.info ISSN 2229 – 5046 SYSTEM WORKING AT FULL / REDUCED CAPACITY,” vol. 3, no. 10, pp. 3737–3744, 2012.

[9] M. S. Bhatt, “Effect of ash in coal on the performance of coal fired thermal power plants. Part I: Primary energy effects,” Energy Sources, Part A Recover. Util. Environ. Eff., vol. 28, no. 1, pp. 25–41, 2006, doi: 10.1080/009083190523235.

[10] I. Okeke, P. Liyang, Y. Qin, C. C. Onwuagbu, A. Paul, and M. Islam, “Effect of Fe2O3 additives on the sintering mechanism of a high strength ceramsite from a CFB fly ash,” Int. J. Adv. Eng. Res. Sci., vol. 12, no. 7, pp. 01–17, 2025, doi: 10.22161/ijaers.127.1.

[11] H. Exchanger, S. In, and A. M. W. C. Power, “INVESTIGATION ON ASH FOULING FORMATION OF INDUCED FAN BLADE AND,” no. x, pp. 1–12.

[12] A. Corsini, F. Rispoli, A. G. Sheard, and P. Venturini, “Numerical simulation of coal fly-ash erosion in an induced draft fan,” Proc. ASME Turbo Expo, vol. 3, no. June, pp. 731–742, 2012, doi: 10.1115/GT2012-69048.

[13] O. Hanne, N. Timo, and K. Hannu, “Increase the utilisation of fly ash with electrostatic precipitation,” Miner. Eng., vol. 19, no. 15, pp. 1596–1602, 2006, doi: 10.1016/j.mineng.2006.07.002.

[14] L. Mishnaevsky, “Root Causes and Mechanisms of Failure of Wind Turbine Blades: Overview,” Materials (Basel)., vol. 15, no. 9, 2022, doi: 10.3390/ma15092959.

[15] S. Mayanda, Y. Yassir, and I. S. Cebro, “Analisis Kerusakan Induced Draft Fan (IDF) menggunakan Vibration Analyzer CSI 2140 dan Dampak Terhadap Daya Output Listrik di PT. PLN Nusantara Power UPK Nagan Raya,” J. Litek J. List. Telekomun. Elektron., vol. 21, no. 2, pp. 155–161, 2024, doi: 10.30811/litek.v21i2.54.

[16] M. Richert, “Thermally Sprayed Coatings for the Protection of Industrial Fan Blades,” Materials (Basel)., vol. 17, no. 16, 2024, doi: 10.3390/ma17163903.

Downloads

Published

2025-10-22