Static Load Evaluation of Kaplan Turbine Shaft in Hydraulic Pump System Using Finite Element Analysis (FEA) Method
Evaluasi Beban Statis Poros Turbin Kaplan Pada Sistem Pompa Hidrolis Menggunakan Metode Finite Element Analysis (FEA)
DOI:
https://doi.org/10.21070/r.e.m.v11i1.1827Keywords:
Turbine shaft, Hydraulic pump, Finite Element Analysis, Von Mises, DeformationAbstract
The turbine shaft is a critical component in hydraulic pump systems as it transmits mechanical energy from the turbine to the pump and experiences combined loads during operation. This study aims to evaluate the structural safety of the turbine shaft geometry under operational loading conditions using the Finite Element Analysis (FEA) method. A three-dimensional shaft model was developed based on actual field measurements and analyzed using SolidWorks Simulation with a torsional load of 6.016 × 10³ Nm calculated from a turbine power of 157.5 kW and a rotational speed of 250 rpm. The shaft material used was SCM4 (AISI 4140). Simulation results show a maximum von Mises stress of 75 MPa with a safety factor of 8.27 relative to the material yield strength. The maximum displacement of 0.4 mm and maximum strain of 2.9 × 10⁻⁴ remain within the elastic range of the material. The results indicate that the shaft design is theoretically safe under static loading; however, indications of wear observed in the field suggest the influence of long-term mechanical degradation during operation.
References
[1] R. L. Mott, Stress and deformation analysis. 2018. doi: 10.1201/9780367853853-8.
[2] Mohammad Asaduzzaman Chowdhury, Lubrication and wear, vol. 180, no. 4600. 1957. doi: 10.1038/1801448a0.
[3] D. Ariwibowo, S. Putra, S. Darmanto, J. Mrihardjono, and W. Mangestiyono, “Failure Analysis Of Water Pump Shaft,” J. Vocat. Stud. Appl. Res., vol. 1, no. 2, pp. 27–30, 2019, doi: 10.14710/jvsar.v1i2.6301.
[4] W. Angga Setiawan, “Analisa Kegagalan Poros Pompa Centrifugal Multistage (GA101A) Sub Unit Sintesa Urea PT. Petrokimia Gresik,” Tek. Mesin ITS, vol. 5, no. 2, pp. 0–5, 2023.
[5] A. Lubis et al., “Stress Concentration Factors of Stepped-Shafts of Circular-to-Square Cross Section under Twisting Moment,” Jur. Tek. Mesin, no. November, pp. 21–23, 2007.
[6] M. H. Henri M Baringbing, “ANALISA KERUSAKAN POMPA VERTIKAL TIPE TAIT MODEL 15BCH-3 DENGAN KAPASITAS 150 L/S DI PDAM TIRTANADI SUNGGAL,” no. 2, p. 57, 2013.
[7] H. Sunandrio and . S., “Analisis Kegagalan Shaft Pompa Submersible Pada Unit Pengeboran Minyak Bumi = Failure Analysis of Pump Shaft Submersible on Oil Drilling Unit,” Mater. Kompon. dan Konstr., vol. 14, no. 1, p. 37, 2014, doi: 10.29122/mkk.v14i1.1653.
[8] S. Hong, “Improvement of lubrication performance in misaligned journal bearings using grooves and rubber under large impact loads,” vol. 16, no. 12, pp. 1–16, 2024, doi: 10.1177/16878132241310482.
[9] R. Alhaffis Firman, Erwen Martianis, Maksum, Ahmad Aidil Rasyid, “Analisis Pengaruh Radius Filler Terhadap Konsentrasi Teganagan Pada Poros Transmisi Baja AISI 1040,” Eng. Sci., vol. 11, no. 1, pp. 608–615, 2025.
[10] W. D. D. F. Pilkey, Shoulder Fillets. JOHN WILEY & SONS, INC., 2007. doi: 10.1002/9780470211106.ch3.
[11] S. R. S. Serope Kalpakjian, Engineering and Technology, vol. 7, no. 5–6. 2021. doi: 10.1177/0270467687007005-605.
[12] Tarumingkeng, “Failure Mode and Effects Analysis,” RUDYCT e-PRESS, no. November, pp. 1–20, 2024.
[13] S. P. Collins et al., AN INTRODUCTION TO PREDICTIVE MAINTENANCE. Butterworth Heinemann, 2021.
[14] C. R. Shigley, J. E., & Mischke, Mechanical Engineering Design. 2019.
[15] C.-M. Hou, Nan; Ding, Ning; Qu, Shen; Guo, Weimin; Liu, Long; Xu, Na; Tian, Linan; Xu, Huixia; Chen, Xiangfeng; Zaïri, Fahmi; Lawrence Wu, “Failure modes , mechanisms and causes of shafts in mechanical equipment © 2022 . This manuscript version is made available under the CC-BY-NC-ND 4 . 0,” Eng. Fail. Anal., 2024.
[16] A. J. Kailani and I. Nuriskasari, “Analisis Kegagalan Poros High Pressure Circulation Pump 1B2 Dengan Metode Elemen Hingga Abstrak,” vol. 4, no. 1, pp. 1051–1061, 2021.
[17] ANSI/ASME B106.1M, “Design of Transmission Shafting THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS,” 1986.
[18] J. K. N. Richard G. Budynas, Shigley’s Mechanical Engineering Design, vol. 11. 2012. [Online]. Available: https://books.google.cl/books?id=eT1DPgAACAAJ
[19] J. Zhou, B. Yang, S. Li, and J. Huo, “Fretting Fatigue Life Prediction of Dovetail Structure Based on,” 2023.
[20] Z. Liu, F. Xu, X. Luan, S. Yu, and B. Guo, “The effect of load on the fretting wear behavior of TC4 alloy treated by SMAT in artificial seawater,” no. December, pp. 1–12, 2024, doi: 10.3389/fmats.2024.1520286.
Published
License
Copyright (c) 2026 Haykal Muzakki, Udin Komarudin, Adhita Prasetia
This work is licensed under a Creative Commons Attribution 4.0 International License.
Copyright Notice
Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution 4.0 International License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
