The Effect of Variations in Impeller Shape on Discharge and Water Pressure on the Pump Prototype Pengaruh Variasi Bentuk Impeller Terhadap Debit dan Tekanan Air Pada Prototipe Pompa

Article Sidebar

Picture in here are illustration from public domain image or provided by the author, as part of their works
PDF XML EPUB
Published: Jun 13, 2022
DOI: https://doi.org/10.21070/r.e.m.v7i1.1632
Keywords:
water pump, impeller design, flowrate, pressure, pompa

Main Article Content

Fajar Riyanto
Teknik Mesin Universitas Muhammadiyah Sidoarjo
Arasy Fahruddin
Teknik Mesin Universitas Muhammadiyah Sidoarjo
Edmundo Tiago Belo
Teknik Mesin, Universidade Oriental Timor Lorosa’e, Timor Leste

Abstract

A pump is a device used to move fluid or something in the form of liquid by increasing the pressure so that it can flow from one place to another or from a low surface to a high surface. In everyday life, the need for water is very useful, so it requires a pump to be able to take it or drain it. In this thesis research will be tested by making a pump prototype using a dynamo drive, and changing the shape of the impeller blade and the number of immersions to determine the resulting water pressure and the resulting water discharge. So that it can find out which impellers are effective in producing water and can drain water faster.

Article Details

Issue
Vol 7 No 1 (2022): June
Section
Articles

Copyright (c) 2022 Fajar Riyanto, Arasy Fahruddin

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

Copyright Notice

Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution 4.0 International License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

References

[1] S. Harahap and M. I. Fakhrudin, “Perancangan Pompa Sentrifugal Untuk Water Treatment Plant Kapasitas 0.25 M3/S Pada Kawasan Industri Karawang,” Semin. Nas. Sains dan Teknol. 2018, pp. 1–9, 2018.
[2] S. Buyung, “Analisis Perbandingan Daya Dan Torsi Pada Alat Pemotong Rumput Elektrik ( Apre ),” J. Voering, vol. 3, no. 1, pp. 1–4, 2018.
[3] A. Muliawan and A. Yani, “Analisa Head Mayor Dan Minor Pompa Chiller Dengan Bukaan Katup Instalasi Pompa Tunggal,” JST (Jurnal Sains Ter., vol. 4, no. 1, pp. 63–69, 2018, doi: 10.32487/jst.v4i1.454.
[4] S. Nugroho and D. Aries Himawanto, “Pengaruh Jumlah Sudu Terhadap Unjuk Kerja Dan Kavitasi Pompa Sentrifugal,” Mekanika, vol. 12, no. 2, pp. 78–83, 2014.
[5] A. Septiyani, A. W. Husodo, and P. Mahardhika, “Analisa Dinamik pada Sistem Perpipaan akibat Getaran Pompa,” Proceeding Conf. Pip. Eng. its Appl., no. 1, pp. 73–78, 2018.
[6] P. Nikosai and I. S. Arief, “Optimasi Desain Impeller Pompa Sentrifugal Menggunakan Pendekatan CFD,” J. Sains dan Seni ITS, vol. 4, no. 2, pp. 6–11, 2015.