Sintesis Komposit Kampas Rem Bebas Asbes Berpenguat Serbuk Kulit Singkong
Asbestos Free Brake Pad Composite Synthesis Reinforced Cassava Peel Powder
-
(1) * Widya Emilia Primaningtyas
Teknik Mesin Institut Teknologi Adhi Tama Surabaya
Indonesia
(2) Rahma Rei Sakura Teknik Mesin, Institut Teknologi Adhi Tama Surabaya
Indonesia
(3) Amir Biqi Teknik Mesin, Institut Teknologi Adhi Tama Surabaya
Indonesia
(4) Chamim Handoyo Teknik Mesin, Institut Teknologi Adhi Tama Surabaya
Indonesia
(*) Corresponding Author
Abstract
An agricultural waste production in Indonesia is increasing as well as the growth of agricultural production. This has become a serious problem in Indonesia. A massive waste will have a negative impact on the health of living things. Therefore, this study aims to provide solutions for the utilization of agricultural waste for the needs of the industry in the automotive sector. In addition, the use of agricultural waste, especially cassava peel waste, can be used as a substitute for brake pads in the form of composite reinforced natural fibers. There are two conditions for cassava peel waste, carbonized and uncarbonized. 50,80,100 Mesh particle size of cassava peel powder used. The composition of the ratio of volume fraction between cassava peel powder and composite epoxy resin used are 20:80; 30:70; and 40:60. The results show that variations in the composition of fibers and resins have an impact on wear values. The best wear resistance shown from the added of 20% cassava peel powder in 100 mesh sizes of particle with 0,00061 ± 0,00039.
References
BPS (Badan Pusat Statistik Republik Indonesia) Statistics Indonesia. [Internet]. Accesed on April 7th, 2014 from http://bps.go.id (nd).
Ma, X., Yu, J., & Kennedy, J. F., “Studies on the properties of natural fibers-reinforced thermoplastic starch composites,” Carbohydrate Polymers, 62(1),19–24, 2005.
Avérous, L., & Halley, P. J., “Biocomposites based on plasticized starch,” Biofuels,Bioproducts and Biorefining, 3(3), 329–343, 2009.
Mohanty, A. K., Misra, M., & Drzal, L. T. , “Sustainable bio-composites fromrenewable resources: Opportunities and challenges in the green materialsworld,” Journal of Polymers and the Environment, 10(1–2), 19–26, 2002.
Dobircau, L., Sreekumar, P. A., Saiah, R., Leblanc, N., Terrié, C., Gattin, R., et al., “Wheat flour thermoplastic matrix reinforced by waste cotton fibre:Agro-green-composites,” Composites Part A: Applied Science and Manufacturing,40(4), 329–334, 2009.
Kuciel, S., & Liber-Knec, A., “Biocomposites on the base of thermoplastic starchfilled by wood and kenaf fiber,” Journal of Biobased Materials and Bioenergy, 3, 1–6, 2009.
Sulistijono, Mekanika Material Komposit, Institut Teknologi Sepuluh November, Surabaya, 2012.
Bram Subakti, “Manfaat Kulit Singkong” Universitas Palangkaraya, Palangkaraya, 2013.
Andi Cahyanto. Sifat Mekanis dan Sifat Fisis Komposit Berpenguat Serat Kulit Jagung dan Serbuk Gergaji Kayu Jati dengan Perbandingan Fraksi Berat 30%:70%,50%:50%,70%:30% Berskin Aluminium Foil untuk Penggunaan Pelapis Dalam Atap, Universitas Muhammadiyah Surakarta, 2012.
Asbestos-free Brake Pad Using Composite Polymer Strengthened With Rice Husk Powder, IOP Conference Series: Materials Science and Engineering, 2018.
M. Taufik Qurohman and Syarifudin, “Analisa Beban Pengereman Terhadap Kualitas Kampas Rem Tromolmobil Dengan Metode Oghosi,” Jurnal Matematika, Vol. 19, No.1, 8 -12, 2016.
Emre G, Akkus A, et al., “Wear resistance of Polymethyl Methacrylate (PMMA) with the Addition of Bone Ash, Hydroxylapatite and Keratin,” 9th International Conference on Tribology (Balkantrib’17), 2004.
Copyright (c) 2018 Widya Emilia Primaningtyas, Rahma Rei Sakura, Amir Biqi, Chamim Handoyo
This work is licensed under a Creative Commons Attribution 4.0 International License.
Copyright Notice
Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution 4.0 International License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
